Archive | Tumbling

How to Bezel Set a Square Stone

Quick Story….. then a tip.

I have always had goals….. In my head. I work towards them, I get new goals, I change my goals, I accomplish some goals, but to be honest, I forget most of them, because I am off running after other shiny goals. I tried something new in the past couple of months, I WROTE DOWN some goals. Long term (Someday), Short Terms (5 and 1 Year), Monthly, Weekly, Daily……. Then, I review it, EVERY DAY. (takes 2 minutes)Ya know what…… These Goals are slowly, and not so slowly becoming reality. I am getting ready to “Kick-Off” something New and Exciting at JewelryMonk.com, that I always had as a goal…. a someday goal…. a dream really more than a goal, that I have had for years and years. But you know what? Just by writing it down and reviewing it every day, It is FAST becoming REALITY.I am still going to hold “This Cat” in the bag so to say, for a little bit, but Stay Tuned here and see What is Coming Next. I really am so excited I can hardly sit here and type.

Now, on with the tip:


How to Bezel Set a Square Stone

 

Today I will demonstrate how I set a square shaped stone in a bezel. It is a little harder that you would think and special attention must be taken when laying out your design, and if the stone has too much room between the edge of the stone and the bezel, the corners will give you “fits”.

First, I am not a HUGE fan of Magnetic Tumbler, but I did tumble this piece in a Magnetic Tumbler to polish underneath the stone and in the hard to get to places, then I place the stone into the setting. I hold the ring in a Ring Clamp and squeeze the bezels together just a bit to hold the stone in place. (which I forgot to take a picture of) Then I place the ring on my Ring Mandrel to support the ring as I press the bezels into the stone, starting at the corners. The corners are the most important part, because if you don’t get the corners tight, there will be a gap.  Start tightening the corners, then work towards the center of the bezel.

Tumbler2  Bezel Setting Rec (1)

Bezel Setting Rec (2)

Bezel Setting Rec (3)   Bezel Setting Rec (4)

Next, after the bezel walls are pushed over the stone to hold the stone firmly in place, I tap lightly on the top of the bezel to force the top of the bezel walls tight around the stone. I use my Chasing Hammer and an old bur to do this, but you can use a Hammer Hand Piece to do this as well. I have cut down the bur to a flat surface with just the slightest dap to it. I also sand the end with 600 Grit Sandpaper to give it a little “grip” and so it won’t slip off the bezel as easy. Be careful not to touch the stone, especially soft stones.

Bezel Setting Rec (5a)   Bezel Setting Rec (5)

Bezel Setting Rec (6)    Bezel Setting Rec (7)

 After the stone is tight and the top of the bezel wall is uniformly up to the stone, take a Snap on Sanding Disc and clean the scratches up. If the scratches are deeper, use a #4 Barrette Needle File first. After the sanding, I use a Knife Edge Rubber Wheel to dress it up and take out the scratches from the sanding.

Bezel Setting Rec (8)   Bezel Setting Rec (9)

Bezel Setting Rec (10)   Bezel Setting Rec (11)

Lastly, I take the piece to the polishing machine and final polish it with Red Rouge.

Bezel Setting Rec (13)   Bezel Setting Rec (14)

There you have it, a tight stone, and I now have a finished piece. The grid work under the stone isn’t really necessary under a cab stone where no light can get through, it just adds a nice touch, but if you have a faceted stone, the extra light it allows will really make it “Pop”.

Bonus: If you want a FREE VIDEO on how to tighten a Bezel Set Stone:

CLICK HERE

As Always, Thanks again for stopping by. If you don’t want to miss out on any FREE CONTENT coming up, Make sure to SUBSCRIBE, like so many others have done, if you haven’t already.

Now, go make someone’s day brilliant!

Doug

Stalled Projects and Afraid-to-Start Projects

In 2 Weeks, WE Could Tackle That Nagging Jewelry Project That Has Been Stalled on Your Bench:


What Projects are you working on, and are stalled….. On have been afraid to try and tackle because you don’t know exactly how to go about it, or are afraid you might mess it up and waste money?

Check out this quick video to see how:

This Jewelry Creation Method Video Course is Focused on:  EDUCATION, EQUIPPING, and ENCOURAGING You in Your Jewelry Making.


JUST The Video Lessons consist of:

1- Video on Image Sizing Video

6- Videos on Wax Preparation and Carving Videos

4- Videos on Casting/ Casting Prep and Investing Videos

3- Videos on SILVER Model Cleanup Videos

1- Video on Mold Making Video

1- Video on Tumbling, Grinding, Pre-polishing Video

2- Videos on Stone Setting Videos

1-Video on Final Polishing and Cleaning Video


  • OVER 20 Bonus Videos covering subjects like Making Your Own Silver Wire, Using a Draw Plate, How to Make Textured Sheet, Annealing, Tool Making, and much, MUCH MORE


  • And the OVER-THE-TOP Bonus:

  • 30 DAY MONEY BACK GUARANTEE!!!

PLUS——->  2 Full Weeks of PERSONAL INSTRUCTIONS with ME,

Doug Napier, The JewelryMonk


So, THAT ought to get you SUPER Excited, But remember:

THIS OFFER ENDS TUESDAY, FEB 21 at Midnight!

So Act Soon, Or This Amazing Offer Will Be Gone!

Together, WE can make the BEST Jewelry of Your LIFE:

Now….. Let’s Make Something Shiny….. TOGETHER

Jewelry Creation Method Video Series is LIVE!

 

INTRODUCING

The Jewelry Creation Method Video Course

Have YOU ever been Overwhelmed by all the seemingly complicated processes that go into jewelry making? How to tackle all the concepts used in the craft? How do you get your design or idea from your mind into jewelry….

There’s Wax Carving – Casting – Model and Mold Making –  Soldering – Stone Setting – Polishing –  just to name a few…… and The list goes on.

Have you ever wanted to take a design that is in your head and create a piece of jewelry from it, one that is repeatable? How much time could you save if you could reproduce one of your handmade designs, over and over, with the same results every time, without recreating the whole piece from scratch?

Are you like me? Do you learn better by examples, rather that books or magazines?

What if someone could show you a Jewelry Creation Method, The Process, The System, ……Step by Step, ….. Every Detail, Every Concept    and TALK YOU THROUGH IT ALL ALONG THE WAY…..

Would that revolutionize your Jewelry Making Experience? If I could Show you how to make your jewelry ideas a reality? Would it open up new opportunities?

This Jewelry Creation Method Video Course is Focused on:  EDUCATION, EQUIPPING, and ENCOURAGING


The Video Lessons consist of:

1 Image Sizing Video

6 videos on Wax Preparation and Carving Videos

4 Videos on Casting/ Casting Prep and Investing Videos

3 Videos on SILVER Model Cleanup Videos

1 Mold Making Video

1 Tumbling, Grinding, Pre-polishing Video

2 Videos on Stone Setting Videos

1 Final Polishing and Cleaning Video

and plenty of bonus material…….PLENTY!


I walk you through every process with 4 camera video perspective

I explain exactly what I am doing, the whole time, and why I am doing it.

And in many cases, show you zoomed in photography of the example, so you completely grasp the concept.

I’ll show you how to master, and understand all of that in your own time.

The bottom line is that we’re going to cover a lot of ground together, over a couple of weeks, and you’re going to come out the other end with a complete understanding of the whole Jewelry Creation Method.

SO, If you’re ready to Take your Jewelry skill-set to the next level, then your next step is clear  click the order button above and get registered for the Jewelry Creation Method Course.

You have a big decision to make. I can’t make it for you… the only thing I can do is tell you that the Jewelry Creation Method Course works.

I promise:    It is not always going to be easy, change and growth never is

But I also promise:     The opportunity to change is always worth the effort.

Click the button now and I’ll see you in the program…

Now, as always…… Let’s Make Something Shiny…..TOGETHER

Doug

JewelryMonk Design Contest Final Update

1st JewelryMonk Design Contest is in the books!


I am finishing up on all the videos, and will make them available soon. There are 19 Main Videos, 19 Bonus Videos, and tons of other content, WHAT A PROJECT!  I had a ton of fun, and look forward to the next contest, Which will be a project all on metal fabrication and soldering. But first, I need a break…. Stay Tuned

NOW….. Go make something shiny!

Doug

JewelryMonk Design Contest Info

jm-design-contest

Alright, the First JewelryMonk Design Contest Info:

(You might want to follow along with this Blog Contest)

Click Here to Subscribe

In a nutshell, here are the details:

I have chosen 5 stones for you to use in a RING design. Your job is to select one of these stones (there is a Pear Shaped, an Emerald Cut Stone, a Marquise Shape, a Trillion Shaped Stone, and an Oval Shaped stone. (Pictured below)

  • You design a SILVER RING with one of these stone.
  • You have a until November 27th at Midnight to submit your design to Doug@JewelryMonk.com
  • The deadline will be Sunday, November 27th 2016 at Midnight EST.
  • My team and I will select 1 winner and announce it December 4th.  The winner will get their design created by myself. During this process, I will create videos of the whole process from:  Design – The Layout – Wax Carving and Cleanup – Casting – Metal Clean up – Rubber Mold Making – Wax Sizing – Casting the Production Piece – Grinding – Tumbling – Pre-Polishing – Stone Setting – and Final Polishing.

I will make this video series available for purchase when it is finished, BUT the winner will receive the series for free.

BUT WAIT!!!! There’s More!!! (I have always wanted to say that….. sorry….. )

The winner will also receive the finished design model, the mold, and the finished piece to own. This design and finished piece is theirs to do with whatever they want.

Also you all have MY PROMISE, that any design that is not selected, I will not use, create, sell, or produce. It will never see the light of day unless you request me to do so. It is your intellectual property, and I will respect that.

Now, don’t feel like you are not “Qualified” to submit a design. You do not have to be a designer to enter. If you can do a CAD drawing, a pencil sketch, or just a crayon sketch, that is all I need.  My career has been creating jewelry from complex designs, or “chicken scratch”. I have an eye for this. We will not make our decision on the design sketch quality, but criteria set up by our team for this project. So this contest is for EVERYONE!

Here are the stones to design from:

Marquise Blue Topaz: 12x6mm and 4mm Deep

blue-mq-jm

Oval Citrine: 9x7mm 4.5mm Deep

citrine-oval-jm

Emerald Cut Amethyst 8x6mm 4mm Deep

em-cut-amethyst-jm

Trillion Cut Garnet 8x8mm 4.75mm Deep

garnet-tri-jm

Pear Shaped Peridot 5x7mm 3.25mm Deep

pear-peridot-jm

So I have 3 things for you to do:

First, Look at the stones you have to work with and choose 1 stone to design a ring with. Take your time and think about it for a bit. REMEMBER, The deadline will be Sunday, November 27th 2016 at Midnight EST. And you only get 1 design to submit…..period (choose wisely my friend)

Second…. Create a design as simple or as complex as you want and email it to Doug@JewelryMonk.com I will print out all these entries submitted and my team and I will choose a winner by December 4th, 2016.

Third and most importantly….. Suscribe for email updates! Along this process I will be releasing videos to highlight certain aspects of the creative process and I wouldn’t want you to miss out.
Click Here to Subscribe

Also, Leave a comment on the website. Let me know you are out there, let me know what you think, and most importantly…. encourage one another. Also check out www.facebook.com/JewelryMonk and do the same there. Encourage one another. Don’t post your designs there…. You would be giving away your secrets, but say HI!, hang out a bit, and most importantly…..HAVE FUN!

There ya have it, the First JewelryMonk Design Contest/Video training series Contest Rules.

I am excited for me, but more importantly, I am excited for YOU ALL. I really look forward to seeing what you all are going to create.

Now…… go create something award winning!

Doug