Day 3 Tools (Graver)

Welcome back to day 3. I had a couple of questions/comments about the graver that I used to shape the earring I made yesterday, so let’s jump into tools and tool maintenance, namely… the graver.

There are many shapes and sizes of gravers available, but if you want to get into hand crafting of metal, get familiar with a few gravers. I will just touch on one today, but at a later date, we will get into a few more styles.

Graver 12

When it comes to metal clean up, getting into those tough to get areas, or just getting a flat clean edge on a piece of silver or gold, my go-to graver is a flat graver. Get yourself a few of these in different widths and see what you can do, it will become a tool that you will grow to love, but when it comes to shaping a graver, there are a few very important things you must do first.

When you buy a new graver, it will have to be shaped and sharpened. This shaping process is VERY important and you must be VERY PATIENT! I cannot express this enough. The hardness of a graver end is heat treated and it is very easy to change it, do to overheating by grinding.

First, get a graver handle. These come in different lengths as well. Find the shortest handle first and mount the pointed end of the graver into it. Your graver will last years and years, and if it gets shorter, then replace the handle with a longer handle to lengthen the blade. I find it easier if you drill a hole into the wood first, (approx 1/8″ drill bit).  There are a few shapes of handles as well, I like the ones that are mushroom shaped with a flat spot cut into it. It fits better in my hand. After you have drilled the hole into the handle, about 1″ deep or so, pound the graver blade into the handle. I find it easiest to place the graver on a piece of wood, like a small 2×4 or something like that, then I pound the handle onto the graver, making sure the bottom edge of the graver is lined up with the flat edge of the handle. After the graver is seated firmly into the handle, place the graver in the palm of your hand so that it sits comfortably. Hold it comfortably so that the graver handle rests in the palm and the graver blade is held in the thumb and forefinger. make a mark on the blade about 1/2 inch past your thumb.

 Graver 9 Graver 5

This is where you will cut off the blade. (they come longer than needed). I use a cutoff wheel to trim the excess off. After it is cut off, the shaping begins. Again, I cannot express how important it is to take your time doing this. Have a cup of water handy and grind the graver for about 1 second, then dip it in the water, grind for 1 second, then dip in the water……repeat, repeat, repeat. You do not want this graver to get hot or it will not work properly, it will chip and break easily or get dull quick.

Grind the blade into the shape of the graver shown, you want the cutting end to come to a thin end, approx 2mm or so, like the graver here:

Graver 1

               Now it is time to sharpen the graver with a sharpening block or a wet stone, there are a number of jigs you can use to set the angle of the graver edge, I try to keep mine at about a 45-50 degree angle:

Graver 7

               Some people like to grind the opposite edge at about a 5-10 degree angle (called a heel) which helps the metal to be removed easier, I just keep mine flat.

Another trick I like to do is to polish the bottom side of my gravers, which leaves a “mirror” finish. I do this by first removing all the scratches on the bottom side of the blade with 600-1000 grit sandpaper, then taking hard yellow polishing compound and rubbing it on a piece of paper, coating the paper with the compound, then rubbing the bottom side of the graver on the paper, polishing it until it is shiny and scratch free. This will make your graver cut silver like butter and give you a super-shiny surface.

 Graver 11 Graver 2

Graver 4 Graver 6

I hope this was not too confusing…… if it was, feel free to comment and ask questions, I will try to clarify if need be.

Now go have fun!

Doug

Day2 Design

1a Locket 01

I guess the first subject to talk about at this point is starting a design. The great thing about designing jewelry is that you have a blank page, if you are making jewelry for yourself, there is no right or wrong design, it is an expression of yourself, and the only limitations are your skills, and that is what we are here to do, hone our skills. If you are making jewelry for others or for the market, then you have to take their likes and desires into consideration.

               There are a number of ways to start to create jewelry, from finding an existing media and turning it into jewelry, to Computer Aided Design (CAD), wax carving, metal fabrication, Precious Metal Clays (PMC), etc. We will touch on all of these things in the future. For the first step let’s look at metal fabrication. I found a design on an antique locket that I would like as an earring. If I could draw, I would but alas, I can’t draw my way out of a paper bag. I found a way to scan the design and get it on a piece of paper. In this instance I used a CAD program, but you can use the original picture, scaled to the size you want, and then I cut and taped it to a flat sheet of sterling silver. I took a very sharp metal scribe and traced around the outside of the picture with a series of small points, just hard enough to make a mark, but not too deep.

1e Locket Earrings 01       1f Locket Earrings 02

After I traced around the design completely, I removed the paper and I have an outline on the silver. (this works on wax as well) I now pierced the silver with a hole large enough to get a saw blade through. I usually use a 3/0 blade, but you can use smaller if you like, I tend to break smaller ones a lot more. after I have the piece completely cut out, I smooth the edges with small “escapement” files and sandpaper, then polish. At a later date we will get into detail on how to best file, sand, and finish pieces, but I figured we would start with an easy way to get your ideas onto metal or wax.  On this piece, I also used gravers and a foredom to give the piece more of a rounded look, but that is what I wanted and that is the cool thing about jewelry making, it is an expression of one’s self as well as a craft.

1g Locket Earrings 03 1j Locket Earrings 08

Finished Amethyst

Thanks for stopping by, I will keep these posts short and to the point in the future, I know we all have busy lives and I would like to give quick tips as opposed to long lessons.

Take care

Doug

Day1, The Beginning

Image

OK, this is day 1, June 1st, 2014. My goal is to try and post once a day for the next 90 days….. WOW, quite an achievement for someone who doesn’t blog at all. I don’t know how this will turn out, but let’s give it a try. I hope to make this a community of people, with feedback, questions, and involvement from many to make and mold us into better jewelry makers

My outline will be, as of today, to focus on different facets of making jewelry each day of the week:

  • Monday Design (Waxcarving, Metalsmith, CAD, Etc)
  • Tuesday (Shaping, Doming, Filing, Grinding, etc.)
  • Wednesday (Soldering, Cold-joining)
  • Thursday (Potpourri, mixed ideas, whatever we come up with)
  • Friday (Reproduction, Casting, Models-Molds, Mold-cutting, Wax-injection, Stamping, etc.)
  • Saturday (Stone Setting: Prongs, Bezels, Channels, etc.)
  • Sunday (Polishing, Finishing, Contrasting Finishes, etc.)

Are you ready for a journey? I am, so lets go…….

Doug

Welcome to JewelryMonk!

Howdy and Welcome to JewelryMonk!

Hand cropped

 

Something new is coming. I am embarking on a journey, something completely new to me, and truthfully something I am kind of uncomfortable with, but am willing to jump in and see what the “water” is like.  I will be sharing tips, tricks, and methods I have learned over the 28+ years I have been in the jewelry industry. I know I can’t take it with me, and am a advocate of passing knowledge down, and being a good steward of the things I have been given.

In the future, we will be adding a podcast (internet radio show), e-books,  and whatever we can to help you become a more well-rounded jewelry maker.

Are you ready? Come along this journey with me!

Doug